The subject of the order is restoration and restaurateur works at four cemeteries from the First World War: Nos 67, 68, 77, 78 in Ropica Górna. The works include comprehensive maintenance and restaurant and recreation of the cemeteries furnishing elements, including: maintenance and reconstruction of stone elements, including walls and fence poles, monument plinths, monuments, tombstones and stelae gravestones; concrete elements, including walls and fence poles, walls and pillars, monuments, tombstones and tombstones, pedestals under crosses and monuments, stairs and fence underwalls; wooden elements, including mantels and fence panels, central crosses; metal: gravestone crosses (cast iron and forged), cast-iron memorative plates; execution and assembly of enamel and cast iron memorative plates; accompanying construction work.

Implementation of the work on the basis of the Conservation Permit No. 122/2016 on 11 April 2016 and amending Decision No 21/2019 of 7 February 2019. The scope of work in accordance with the programme of restoration works of cars. Mark Sawicki from November 2015 and the Historical and Recreation Documentation of cars. George Drogomir's 2012 cemetery partially renovated in 2017 with deviations from recreation documentation. For maintenance: stone wall fence with gate poles and intermediate pillars — length approx. 70 m2 (approx. 350 m2 thread); - concrete covers of masonry and pillars — approximately 80 m2 (surface approx. 60 m2). For the maintenance of the current tombstone with cross type M — 10 pcs and stelae — pcs. 5 and 15 tin enamel plates; stone monument plinth under the central cross — approx. 50 m2); wooden cross (reconstituted in 2017) with the necessary replacement of tin roofing with proper, compliant documentation recreation — should be modeled on the cross set in graveyard no. 66 of Malaste or no. 76 of Siara. To make wooden elements of the fence with a gate with dimensions in accordance with the recreation documentation, i.e. using irregular spacing between posts and gates; where possible, material from the existing wooden section of the fence can be used when subjected to current maintenance; length of the wooden panel — 10 m.b; formation of graves in the form of mogilic blankets covered with sandstone slabs (stones) of height adjusted to the height of the mounds with the possibility of using previously used stones of the appropriate size — length of stone edging approx. 96 m2; inscription plate made of gray marble to be mounted on the pedestal of the cross with sizes tailored to the niche in the pedestal and content: EUER STREITEN HAT DIE GANZE ERDE ERSCHÜTTERT, DOCH DAS KREUZ DER VERSÖHNUNG IST AUFRECHGEBLECT IEBEN. Shade of stone, type of letters, their size and arrangement of verses to be agreed with the Ordering Party.

Implementation of work on the basis of Conservation Permit No. 58/2016 of 22 February 2016 and Amending Decision No 20/2019 of 7 February 2019. The scope of work in accordance with the programme of restoration work of cars. Mark Sawicki from November 2015 and the Historical and Recreation Documentation of cars. George Drogomir's 2018 cemetery largely preserved in historic layout. According to the recreation documentation, it is necessary to correct the locations of 6 tombstones (no. 1,2,5,6,7,8) and replace the unoriginal tombstone for mogile number 5 with a valid copy. For preservation: stone masonry with monument wall and high pillars of entrance with pylon shape with concrete covers (approximately 97 m2) - stone steps with cheeks and the surrounds of the main avenue (approximately 17 m2) and its stone pavement - concrete pedestals under crosses -17 pcs. (including 1 to replace with the correct copy, pay attention to the decorative finish of the surface) - cast iron crosses of 17 pcs, including 13 type M and 4 type. For recreation and installation on the monument wall a wooden cross and wooden wicket according to the recreation documentation. It is necessary to mount on the lower terrace a light concrete curb connecting the lower edges of the cables: 12-14 and 15-17 (approx. 14 m2). Currently based on the fence wall, the HV stone border post must be dug in at any corner of the fence. To make and mount on plinths enamelled plates - 17 pcs including 16 round pcs with a diameter of 15 cm and 1 piece oval 19x26 cm — according to designs from the recreation documentation. It is necessary to make and mount in the cavity of the monument wall a marble plaque (gray marble) with an inscription (approx. 104 cm x 108 cm) — according to the recreation documentation. Shade of stone, type of letters, their size and arrangement of verses to be agreed with the Ordering Party.

Implementation of work on the basis of Conservation Permit No. 128/2016 of 11 April 2016 and Amending Decision No 22/2019 of 7 February 2019. The scope of work in accordance with the programme of restoration works of cars. Mark Sawicki from November 2016 and the Historical and Recreation Documentation of the cars. Izabeli Chlost and Jerzy Drogomir from 2012. For preservation፦ stone fence wall with monument wall with total pow. approx. 750 m2 with concrete covers of about 125 m2 and stone entrance staircase (6 degrees); - concrete elements with the necessary scope of restoration destroyed (after arrangement with the conservation services) or missing, whereby special attention should be paid to the finishing of the gravestones surface according to the original: concrete pedestals under the crosses of type H and - 40 pcs., concrete tombstones with crosses of type U, N and — 8 pcs., concrete stelae 22 pcs.: 4 large and 18 smaller (in historical documentation bearing the letters a and c, respectively) symbols), with 2 large and 11 smaller stelae for preservation, and 2 large and 7 smaller; metal tombstone crosses of the types listed above (together 48): including 33 H type, 7 pcs. Type U , 1 pcs of type N and 4 pcs of type, with the decision to repair or replace crosses damaged by copies after agreement with the conservation services - 4 cast iron plates: 2 of it. 39,5 x 60 cm and 2 of it. 15x24 cm. For restoration, the metal gate and the railing of the stairs, the crowning element of the gate made of the reinforcing bar must be removed. For manufacture and installation፦ 2 cast iron plates of the right. 39,5 x 60 cm - 1 cast iron board 15 x 24 cm - 2 rectangular enamelled tin plates 15 x 24 cm - 15 rectangular enamel plaques of it. 26 x 34 cm - 41 round enamelled tin plates with sawn. r. 15 cm Method assembly described in historical documentation. Note: Cast iron plaque listed in the recreation documentation for grave 6/2 — Pattern 3 is preserved and requires maintenance rather than order as new) The layout of the tombstones must be performed according to the archival plan. Most tombstones (crosses and stele) require relocation and setting in new places on ground-poured foundations. After ordering the location of the cogs, according to historical documentation, the course of the avenue and the outlines of several half-graves - the total length of curbs approximately 345 m.b. The wooden central cross has already been reconstituted and requires current impregnation. For the execution and installation of an array of gray marble with dimensions adapted to niches with inscription (69 letters) with content WOLLT IHR DIE HEIMGEGANGENEN HELDEN EHREN, SCHENKT EURER HERZ DER ERDE, DIE SIE DECKT. Shade of stone, type of letters, their size and arrangement of verses to be agreed with the Ordering Party.

Implementation of work on the basis of the Conservation Permit No. 46/2016 of 22 February 2016 and amending Decision No 19/2019 of 7 February 2019. The scope of work in accordance with the programme of restoration work of cars. Mark Sawicki from November 2015 and the Historical and Recreation Documentation of the cars. Izabela Chlost and George Drogomir from 2013. It is necessary to recreate the historical layout of quarters, self-contained graves, networks of passages and alleys. The plinths under the crosses exist in the cemetery are set out in accordance with the archive plan and require recreation and setting according to the drawings from the recreation documentation - larger under the crosses of type M- 34 pcs. - smaller under crosses of type - 26 pcs. Crosses should be forged from pedestals and undergo maintenance. The others perform as replicas according to documentation. For preservation: stone fence wall with corner and gate posts and pillars of the monument element approx. 925 m2; concrete covers of masonry and pillars approx. 145 m2; reinforced concrete beam crowning the monument form — approx. 50 m2; wooden gate (possible reconstruction); cast iron crosses of type M - 17 pcs. , (others to be recreated), cast-iron crosses type - 26 pcs., excess crosses — 9 pcs. — for use in other cemeteries or for reimbursement to the Ordering Party. For opening: concrete plinths under crosses of two types - a total of 60 pcs. (note: in this cemetery, pedestals used originally and during renovation are inappropriate for M-type crosses, hence according to the proposal of the author of the historical and recreation documentation on page 7, they should be replaced with specific type, in accordance with Figure No 3); cast iron crosses type M - 17 pcs.; borders of quarters and mole along with the layout of paths and avenues with the help of stone curbs — approximately 540 m.b.; wooden central cross according to the archive design and the design of the cars. Konrad Kochański annexed to the Programme of Conservation Works (should be modeled on the cross set in the cemetery number 66 Małastów or No. 76 of Siara). For the execution and installation of 60 enamel plates, including 26 round diameter 15 cm. and 34 oval with the right. 19x26 cm.