The subject of the contract is the performance of the task entitled Modernization and reconstruction of the school building in Janowice and purchase of a school bus, which includes.

Part 1: Development of the area around the School Building in Janowice

Part 2: Thermomodernization with reconstruction and extension of the School Building in Janowice

Part 3: Purchase of a low-emission hybrid school bus

The subject of the contract is the preparation of purposeful multi-branch design documentation, along with obtaining legally required checks, arrangements, permits, etc., with the submission of an application for a building permit or notification to the competent administrative body, and the execution of construction works indicated in this documentation.

The scope of works includes:

- Installation of sanitary sewer made of PVC pipes laid at a depth of up to 3.0 m on a sand substrate, in an unfortified trench. Performing a leak test of the duct. Backfill of the trench with a manual layer of thick sand. 30 cm, then earth from the trench. Manual spreading of excess land.

Connection - diameter 160 mm.,

- Drainage of rainwater from the parking lot with sand, oil and grease catchers; PVC pipes laid at a depth of up to 3.0 m, on a sand substrate, in an unfortified trench. Performing a leak test of the duct. Backfill of the trench with a manual layer of thick sand. 30 cm, then earth from the trench. Pipes with a diameter of 160mm.,

-External. installation of rainwater cante made of PVC pipes with diameter. 110mm with inspection manholes with diam. 60mm

- Lighting line in its own area with 16 LED lamps with a height of 4m,

- Pavements with bet cubes. 6 cm thick, chamferless, on CEM ballast. - sand with a thickness of 5cm and sand.

- Internal roads made of concrete blocks with a thickness.8cm on a foundation made of mineral aggregates and sand with curbs,

- Parking lots made of concrete blocks with a thickness.8cm on a foundation made of mineral aggregates and sand,

- Green areas; lawn on humus substrate with a thickness of 10cm in a 3m strip around the investment area,

- Fencing of the area; steel wire with diam. 4.2mm, system with a height of 1.5m with 1 wicket with a width of 1m,

- Widening of the slope by 2m, sand/gravel compacted.

The subject of the contract is the preparation of purposeful multi-branch design documentation, along with obtaining the legally required checks, arrangements, permits, etc., with the submission of an application for a building permit or notification to the competent administrative body, and the execution of construction works indicated in this documentation

The scope of works includes:

- Demolition of the stairs of the outer arcades of the main entrance.

- Demolition of the sidewalk for the plan. Expansion

- Demolition of the surface paved with grit for the plan. parking and road, up to depth 50cm

- Dismantling windows with external and internal window sills. and exterior doors

- Dismantling of trapezoidal sheet metal on the roof along with wooden battens.

- Dismantling of cast iron radiators in the school part 'A'.

- Ramp for people npspr made of galvanized steel grating and concrete stairs covered with gres tiles with powder coated steel balustrade.

- External stairs of the main entrance, concrete, covered with porcelain tiles with powder-coated steel balustrade.

- Making a 30cm wide band around the building from stone pebbles on sand.

- Extension with a sanitary part - foundations, load-bearing walls, reinforced concrete ceilings, wood. roof structure with metal tiles, external and internal finish. and technical infrastructure (turnkey).

- Replacement of PVC windows and ALU exterior doors; 2-chamber (3-pane)

- Installation of fire-smoke-tight doors to staircases

- Preparation of external walls before insulation with mineral wool, breaking a. plaster, cavity replenishment, alignment, etc.

- Insulation of external walls with mineral wool 18cm thick with silicate plaster on a grid with 2x glue (system)

- Insulation of the outer walls of the plinth and foundation with waterproof polystyrene foam with a thickness of 15cm on glue, bucket foil

- Restoration of the corner buttresses of the building.

- Restoration of the plinth of the building from stone tiles, on glue.

- Repair of the roof truss; replacement of degraded elements, biol impregnation. and fire protection, new patches

- Laying a new roof slope made of metal tiles with waterproofing.

- Insulation of the ceiling above the first floor (attic) with mineral wool 30cm thick with a floor made of gypsum and fiber boards on joists.

- Installation of roofing elements (downspouts, gutters and fittings).

- Installation of lightning protection system.

- Installation of external lighting on the building and antenna installations on the roof.

- Installation of wall-mounted convector plate radiators in the school part 'A'.

- Sanitary fittings, sinks, toilet bowls, shower, urinals

The subject of the contract is the purchase and delivery of a brand new low-emission school bus with hybrid drive and appropriate equipment, meeting the conditions and technical requirements set out in the current legislation.

1) Bus dimensions:

• length from 11.80 to 12.50 m

• height up to 3.2 m

• permissible total width not more than 2.55 m (in accordance with the Regulation

on the technical conditions of vehicles)

2) Number of seats to carry passengers:

40 - 45 seats (four full-size seats are allowed

folding or easily removable seats in the wheelchair space)

(3) drive, number and type of axle:

• diesel engine, with a capacity of min. 6.5 l meeting the minimum standard. EURO 6E, power min. 220 kW,

• equipped with a mild-hybrid module,

• engine equipped with an automatic engine oil replenishment system,

• automatic transmission, min. 5-step,

• rear drive axle – gear ratio selected in an optimal way minimizing

diesel consumption,

• front axle – disc brakes with automatic adjustment and indication of brake pad wear. Independent suspension with stabilizer,

• exhaust pipe on the roof,

• the degree of emission reduction according to EURO 6E,

• oil level gauge,

• design maximum speed 90 km/h,

• automatic transmission gear selector, 3-button (D-N-R),

• vehicle with 48V hybrid system;